- 您现在的位置：买卖IC网 > Sheet目录279 > 101-1147 (Rabbit Semiconductor)KIT RIO PROGRAM I/O
Starting Dynamic C
Once the RCM4110 is connected as described in the preceding pages, start Dynamic C by double-clicking on
the Dynamic C icon on your desktop or in your Start menu. Dynamic C uses the serial port specified during
installation.
If you are using a USB port to connect your computer to the RCM4110, choose Options > Project
Options and check “Use USB to Serial Converter” in “Serial Options.” Click OK to save the settings.
Run a Sample Program
Use the File menu to open the sample program ROTATELED.C in the Dynamic C SAMPLES\RIO folder.
Press function key F9 to compile and run the program.The four LEDs on the Prototyping Board will flash on
and off in a rotating sequence, and the Dynamic C STDIO window will open on your PC to display the status
of the Rabbit RIO chip’s Channel 1.
This sample program uses Channel 1 with the Rabbit RIO chip operating in the SPI clocked serial communi-
cation mode. The Rabbit RIO Chip User's Manual describes the communication modes in more detail.
Where Do I Go From Here?
If the sample program ran fine, you are now ready to go on to other sample programs and to develop your
own applications. Application Note AN415, RIO Programmable I/O Kit , discusses how to use the Prototyp-
ing Board and explains the sample programs and Rabbit RIO function calls. The source code for the sample
programs is provided to allow you to modify them for your own use. The RCM4100 User's Manual on the
Dynamic C CD also provides complete hardware reference information and describes the software function
calls for the RCM4110 RabbitCore module, and the Rabbit RIO User's Manual provides complete reference
information for the Rabbit RIO chip.
Troubleshooting
If Dynamic C cannot find the target system (error message "No Rabbit Processor Detected." ):
? Check that the RCM4110 is powered correctly — the red power LED on the Prototyping Board should be
lit when the RCM4110 is mounted on the Prototyping Board and the AC adapter is plugged in.
? Check both ends of the programming cable to ensure that they are firmly plugged into the PC and the
PROG connector, not the DIAG connector, is plugged in to the programming port on the RCM4110.
? Ensure that the RCM4110 module is firmly and correctly installed in its socket on the Prototyping Board.
If there are no faults with the hardware, select a different COM port within Dynamic C. On your computer,
open Control Panel > System > Hardware > Device Manager > Ports and look at the list of available
COM ports. In Dynamic C, select Options > Project Options , then select one of the available COM ports
on the “Communications” tab, then click OK . Press <Ctrl-Y> to force Dynamic C to recompile the BIOS. If
Dynamic C still reports it is unable to locate the target system, repeat the above steps for another available
COM port. You should receive a Bios compiled successfully message once this step is com-
pleted successfully.
If a program compiles and loads, but then loses target communication before you can begin debugging, it is
possible that your PC cannot handle the default debugging baud rate. Try lowering the debugging baud rate.
? Locate the Serial Options dialog in the Dynamic C Options > Project Options > Communica-
tions menu. Choose a lower debug baud rate.
If there are any other problems:
? Use the Dynamic C Help menu to get further assistance with Dynamic C.
? Check the Rabbit Semiconductor Technical Bulletin Board at www.rabbit.com/support/bb/ .
? Use the Technical Support e-mail form at www.rabbit.com/support/ .
NOTE: If you purchased your RIO Programmable I/O Kit through a distributor or through a Rabbit
Semiconductor partner, contact the distributor or partner first for technical support.
020–0124
?
070715–C
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
101-606
CONN SOCKET IDC 60POS W/KEY GOLD
10113616-01531LF
CONN MOD JACK 8PORT 8/8 R/A PCB
10117863-5036010LF
CONN MOD JACK 8/8 R/A PCB
10118061-5005010LF
CONN MOD JACK 2PORT 8/8 R/A PCB
10118062-5001310LF
CONN MOD JACK 4PORT 8/8 R/A PCB
10118063-5001310LF
CONN MOD JACK 6PORT 8/8 R/A PCB
10118064-5001310LF
CONN MOD JACK 8PORT 8/8 R/A PCB
10118065-5005310LF
CONN MOD JACK 4PORT 10/8 R/A PCB
相关代理商/技术参数
1011150000
功能描述:TERM BLK W/LED 300 10A GRAY RoHS:是 类别:连接器，互连式 >> 接线座 - Din 轨道，通道 系列:W 标准包装:1 系列:CLIPLINE UK 类型:断连 断开类型:保险丝，杆 位置数:3 级别数目:1 端子 - 宽度:18.0mm 端接类型:螺钉 电流 - IEC:32A 电压 - IEC:690V 电流 - UL:30A 电压 - UL:600V 线规或范围 - AWG:3-18 AWG 线规或范围 - mm²:1.5-25mm² 特点:- 颜色:黑 保险丝类型:小型，10.3mm x 38mm 材料 - 绝缘体:聚酰胺（PA），尼龙 材料可燃性额定值:UL94 V-0 剥线长度:12mm 其它名称:UK 10.3-HESI N 3POLUK10.3-HESIN3POL
10-111505
制造商: 功能描述: 制造商:undefined 功能描述:
10111510202
制造商:Amphenol PCD 功能描述:MODULES - Bulk
10111510402
制造商:Amphenol PCD 功能描述:MODULES - Bulk
10111510502
制造商:Amphenol PCD 功能描述:MODULES - Bulk
10-111514
制造商: 功能描述: 制造商:undefined 功能描述:
10111519-90300YYLF
制造商:FCI 功能描述:500-20ZF-PWRBLADE ASSYS - Bulk
10111520-90045YYLF
制造商:FCI 功能描述: